Cable Tray
supplier in Saudi Arabia
Perforated cable tray, bends, tees, risers and reducers, with strut channel, brackets, covers and hardware. Fabricated in the Kingdom to your sizes, in hot-dip galvanized, pre-galvanized, stainless steel, aluminum or powder coated, and delivered across Saudi Arabia.
Perforated cable tray
Fabricated in the Kingdom to the width, height and length on your drawing, in hot-dip galvanized, pre-galvanized, stainless steel, aluminum or powder coated.
Any size
Made to your drawing
5 finishes
Galvanized, stainless, aluminum
Explore cable tray.
See every product ›Perforated cable tray
Slotted base and sides, cut to the width, height and length on your drawing.
Hot-dip galvanized tray
Dipped after fabrication, so every edge and hole is coated. Our most common finish.
Pre-galvanized tray
Formed from galvanized sheet, smooth and economical for dry indoor runs.
Tray fittings
Flat bends, tees, crosses, risers and reducers, made to match your tray.
Strut channel
41 x 41 and 41 x 21 slotted channel, with brackets, hangers and hardware.
Built for Jeddah air.
Heat, sand, salt and sun. Tell us where the tray runs, and we fabricate it in the finish that lasts there.
Where will the tray run?
Pre-galvanized steel
Galvanized sheet, cut and formed. Clean, smooth and the most economical choice for offices, ceiling voids and air-conditioned plant rooms.
Lowest cost
Of the steel finishes
Indoors
Dry, conditioned spaces
Hot-dip galvanized steel
Dipped after fabrication, so the zinc covers every cut edge, hole and weld. Our most common finish, with covers to keep sun and sand off the cables.
Most common
Our standard finish
Edges coated
Galvanized after cutting
Stainless steel or aluminum
Stainless steel stands up to salt air, chemicals and washdown. Aluminum is light, easy to handle at height and does not rust.
Stainless
Salt air and chemicals
Aluminum
Light, does not rust
Powder coated
A coloured coat over the steel, to match the building or to mark a service such as fire alarm or data.
Any colour
To match or to mark
Clean finish
For exposed runs
Hot-dip galvanizing after fabrication also coats the cut edges and holes, which pre-galvanized sheet leaves bare.
Cable tray, strut channel or conduit?
Open
Easy to add to
Slotted
Bolt-on, adjustable
Enclosed
Fully protected
Many power and control cables, side by side
What it carries
Single cables, conduit and equipment, clamped
What it carries
A few circuits, pulled through
What it carries
Lay new cables into the open tray
Adding cables later
Add another clamp along the slot
Adding cables later
Pull them through, if there is room
Adding cables later
Main routes in plant rooms, risers and ceilings
Where it fits best
Short runs, and frames that hold trays and panels
Where it fits best
Final runs to lights, sockets and machines
Where it fits best
Covered or open cable tray?
Covered tray for roofs and outdoor runs.
A cover keeps direct sun, sand and falling objects off the cables. Choose it for roofs, open plant areas and anywhere the run is exposed.
Ask for tray covers ›Open tray indoors.
Indoors, an open perforated tray lets the cables breathe and cool, and new cables can be laid in at any time without opening anything.
Ask for perforated tray ›Finish the system.
Shop online ›Conduit and fittings
EMT, rigid and flexible conduit for the final runs off the tray.
Explore ›
Distribution equipment
Armoured and unarmoured cables to lay in the tray, plus breakers and boards.
Explore ›
Cable accessories
Ties, glands and lugs to fix and finish every cable.
Explore ›
Earthing
Earth bars and copper tape to bond every tray run.
Explore ›
The full range.
Request a quote ›Tap any product to ask for a price on WhatsApp. Or send the drawing or the tray schedule, and we price the whole route together.
Tray, fittings and supports
Perforated cable tray
Cut to your drawing in hot-dip galvanized, pre-galvanized, stainless steel, aluminum or powder coated.
Ask for a price ›Hot-dip galvanized tray
Galvanized after fabrication, for outdoor, roof and plant runs.
Ask for a price ›Pre-galvanized tray
Galvanized sheet, cut and formed, for dry indoor runs.
Ask for a price ›Tray fittings
Bends, tees, crosses, risers and reducers to match your tray.
Ask for a price ›Strut channel and supports
41 x 41 and 41 x 21 channel with brackets, hangers and hardware.
Ask for a price ›
Covers and special sizes
Tray covers for roofs and outdoor runs, and any size from your drawing.
Ask for a price ›Built to the standards on your spec.
Send the specification or the tray schedule. We fabricate every length and fitting to the size, finish and standard it names, and tell you straight away if an item needs an approved equivalent.
IEC 61537
Cable tray systems
Cable tray and cable ladder systems for cable management.
NEMA VE 1
Metal cable tray
Metal cable tray systems, the North American standard.
NEMA VE 2
Installation
Guidelines for installing cable tray.
ISO 1461
Hot-dip galvanizing
Hot-dip galvanized coatings on fabricated iron and steel articles.
ASTM A123
Hot-dip galvanizing
Zinc coatings on iron and steel products galvanized after fabrication.
EN 10346
Pre-galvanized sheet
Continuously hot-dip coated steel sheet, the base for pre-galvanized tray.
Why Al Barq is your cable tray supplier.
Approved by Aramco, SEC and NWC.
Al Barq United Trading Co. is an approved supplier to Saudi Aramco, the Saudi Electricity Company and the National Water Company, and is ISO 9001 certified. Our cable tray goes into the plants, substations and buildings those approvals cover.
Made in the Kingdom.
Cut to your sizes and finished for your site, then delivered across Saudi Arabia.
Walk in and ask.
Al Aziziyah District, Jeddah. Saturday to Thursday, 8:30 to 1:30 and 4:30 to 8:30.
Questions, answered.
Can't find your answer? Send us your drawing and we will come back with a quote.
Contact sales › Where can I buy cable tray in Saudi Arabia?
At Al Barq United Trading Co. in Al Aziziyah District, Jeddah. We fabricate perforated cable tray, fittings and supports in Saudi Arabia to your sizes, in hot-dip galvanized, pre-galvanized, stainless steel, aluminum or powder coated, and deliver across the Kingdom. Send your drawing or list on WhatsApp at +966 58 144 4604 for a quote.
Pre-galvanized or hot-dip galvanized cable tray?
Pre-galvanized tray is cut and formed from galvanized sheet, so it is smooth and economical, but the cut edges are bare. Hot-dip galvanized tray is dipped after fabrication, so every edge, hole and weld is coated. Use pre-galvanized indoors where it stays dry, and hot-dip outdoors, on roofs and in plants.
When should I use stainless steel or aluminum tray?
Stainless steel suits coastal sites, chemical plants and washdown areas, where salt and chemicals attack zinc. Aluminum is light, does not rust and is easy to handle at height.
What sizes of cable tray can you make?
Any width, height and length on your drawing. Bends, tees, crosses, risers and reducers are made to match the tray, in the same finish.
How much load can a cable tray carry?
It depends on the tray width and height, the steel thickness and the distance between supports. Send the cable schedule and the support spacing and we size the tray to carry it.
Do I need covers on outdoor cable tray?
On roofs and outdoor runs, a cover keeps direct sun, sand and falling objects off the cables. Indoors, open tray lets the cables cool and makes it easy to add cables later.
How do I earth a cable tray?
Keep the run electrically continuous across every joint with splice plates or bonding jumpers, and bond it to the earthing system as your specification sets out. Our earthing page has the copper tape and earth bars.
What supports do you supply with the tray?
Slotted strut channel in 41 x 41 and 41 x 21, wall brackets, cantilever arms, hangers and threaded rod, splice plates, and the nuts and bolts to fix it all.
How long does fabrication take?
It depends on the size, finish and quantity, and hot-dip galvanizing adds a step after fabrication. We confirm the delivery time with the quote.
Do you deliver cable tray outside Jeddah?
Yes. We deliver across Saudi Arabia, including Riyadh, Dammam, Jubail, Makkah, Madinah, Tabuk and Abha. Tell us where the order is going when you send your list.
Not sure which tray?
Send us three things. We come back with the tray, fittings and supports you need, and a quote.
